|
2-2-19-sborka-privoda-mekhanizma-gazoraspredeleniya.html
2.2.19. Assembly of the drive of the mechanism of gas distributionEstablish an asterisk of a bent shaft.
Establish a chain of the oil pump.
|
|
Fig. 2.189. Fixing of a chain of the oil pump special adaptation
|
Record an asterisk of the oil pump special adaptation (fig. 2.189). Establish a guide of a chain of the oil pump.
Establish a natyazhitel of a chain of the drive of the oil pump.
|
|
Fig. 2.190. Installation of special adaptation on a cam-shaft
|
Install special adaptation on a cam-shaft, then install the piston of the first cylinder in the provision of VMT (fig. 2.190). Remove the lower cap of the block of cylinders.
Turn a bent shaft clockwise to cylinder No. 1 piston VMT.
Establish a gas distribution mechanism drive chain.
|
|
Fig. 2.192. Installation of a natyazhitel of a chain
|
Establish a natyazhitel of a chain and remove the holding wire (fig. 2.192).
Hold a cam-shaft, using a suitable wrench on a hexagon, as shown in the figure 2.193. Tighten a fixing bolt of an asterisk of the camshaft.
Inhaling moment: 69–75 N · m.
Apply pure engine oil on a forward epiploon of a bent shaft.
Slightly press an epiploon a hand.
Press an epiploon, using special adaptation and the hammer.
|
|
Fig. 2.194. Places of putting sealant on a forward cover of the engine
|
Apply kremniyevoorganichesky sealant on a forward cover of the engine, as shown in the figure 2.194.
|
NOTE
Establish a cover of a head of the block of cylinders in 10 min. after putting sealant.
Kremniyevoorganichesky sealant is not required in the area C shown in the drawing as it there is already available (L3 with the mechanism of change of phases of gas distribution).
|
Thickness:
A: 2,0–3,0 mm;
B: 1,5–2,5 mm.
|
|
Fig. 2.195. Order of tightening of bolts of fastening of a cover of a head of the block of cylinders
|
Establish bolts of fastening of a cover of a head of the block of cylinders in the order specified in the figure 2.195.
|
|
Fig. 2.196. Installation of a lock bolt on a pulley of a bent shaft
|
Turn a bent shaft clockwise to cylinder No. 1 piston VMT.
Hold a pulley of a bent shaft from a provorachivaniye by means of special adaptation (fig. 2.197). Tighten a bolt of fastening of a pulley of a bent shaft in two steps.
Tighten to 96–104 N · m.
Tighten on 87-93 °.
Turn off a bolt of M6x1,0.
Remove special adaptation from a cam-shaft.
Remove special adaptation from an opening of the lower cap of the block of cylinders.
Turn a bent shaft clockwise on two turns to the provision of VMT.
If the provision of VMT does not manage to be reached, weaken a fixing bolt of a pulley of a bent shaft and repeat actions.
Establish the lower cap of the block of cylinders.
Inhaling moment: 20 N · m.
Apply kremniyevoorganichesky sealant on the interfaced surfaces, as shown in the figure 2.198.
|
NOTE
Establish a cover of a head of the block of cylinders in 10 min. after putting sealant.
Diameter of a point: 4,0–6,0 mm.
|
Establish a cover of a head of the block of cylinders with new laying.
|
|
Fig. 2.199. Order of tightening of bolts of fastening of a cover of a head of the block of cylinders
|
Inhaling moment: 8,0–12,0 N · m.
| 